Category Archives: Heating Cable

New product on our website: Chromalox PJB Rain Tight Junction Box for use with SSK. Use With: SRL, SRM/E, CWM, SRF

New product on our website: Chromalox PJB Rain Tight Junction Box for use with SSK. Use With: SRL, SRM/E, CWM, SRF

https://morelectricheating.com/products/MANUFACTURERS/CHROMALOX/HEATCABLE/PJB.aspx

PJB Rain Tight Junction Box for use with SSK
• Use With: SRL, SRM/E, CWM, SRF
• Third-party certifications: UL Listed, CSA, FM

Polycarbonate watertight enclosure for use with SSK

New product on our website: Chromalox UBC Line Sensing Thermostat Power Connection Kit for use With SRL, SRP, SRM/E, CWM, SRF, HWM

New product on our website: Chromalox UBC Line Sensing Thermostat Power Connection Kit for use With SRL, SRP, SRM/E, CWM, SRF, HWM

https://morelectricheating.com/products/MANUFACTURERS/CHROMALOX/HEATCABLE/UBC.aspx

UBC Line Sensing Thermostat Power Connection Kit
• Use With SRL, SRP, SRM/E, CWM, SRF, HWM

NEMA 4X rated junction box designed to connect a single SRL, SRP, SRM/E or CWM cable run to power and control cable output via pipe temperature in non-hazardous areas. This kit provides water-resistant cable entry for one cable, enclosure support, terminal block and a water resistant corrosion resistant wiring enclosure with a 3/4″ opening to accept a conduit hub (CCH- 2 or equal). Stainless steel bulb is 1/4″ diameter x 7-1/4″ long with 3ft capillary. Switch rated for 22 amps SPDT 120-480 volts. Operating temperature range is -40°F to 160°F (-40°C to 71°C). Temperature set point 0° to 400°F (-81°C to 200°C) with 10°F.
* Only Approved for Ordinary Areas.

New product on our website: Chromalox B100 & E100 Heat Trace/ Freeze Protection Thermostats

New product on our website: Chromalox B100 & E100 Heat Trace/ Freeze Protection Thermostats

https://morelectricheating.com/products/MANUFACTURERS/CHROMALOX/HEATCABLE/B100-E100.aspx

B100 & E100 Heat Trace/ Freeze Protection Thermostats
• ±1% Setpoint Repeatability
• E100 Remote Mount for Heat Trace (Bulb & Capillary)
• 22 Amp Resistive Switch
• Single and Dual Output Models
• Fast Response for Protection of Valves and Piping
• NEMA 4X, 7 and 9 Enclosures
• Third-party certifications: UL Listed, CSA, FM (models E121/122, B121 only)

Maintaining proper viscosity and flow is critical in heat trace or freeze protection applications. The E100 remote mount thermostats utilize a stainless steel bulb and capillary design to accurately sense temperature at key points along a pipe. The B100 direct mount thermostats feature liquid-filled thermal assemblies and sense air temperatures from 15 to 140°F. Both models are epoxy coated to seal from moisture and contaminants in compliance with NEMA 4X requirements. NEMA 7 stats E121/122/122P and B121 are designed for Class I, Division I and 2, Groups B, C, D, and Class 2, Division I and 2, Group E, F, G.

New product on our website: Chromalox HSRM Self-Regulating Medium Temperature for Process Temperature Maintenance

New product on our website: Chromalox HSRM Self-Regulating Medium Temperature for Process Temperature Maintenance

https://morelectricheating.com/products/MANUFACTURERS/CHROMALOX/HEATCABLE/HSRM.aspx

HSRM Self-Regulating Medium Temperature
• Approximate Size 3/8″W x 1/8″H
• Available in 5, 8, 10, 15, 20 Watts per Foot
• Available in 120 and 208-277V models
• Third-party certifications: CSA, FM
• Process Temperature Maintenance to 302°F (150°C)
• Maximum Continuous Exposure Temp, Power Off, 425°F (215°C)
• Circuit Lengths to 750 Feet
• T-Ratings see data sheet
• Min. Install Temp = -76°F (-60°C)
• Min. Bend Radius 1-1/8″
• For Use on Metal Pipes and Tanks

• Energy efficient, self-regulating HSRM uses less energy when less heat is required.
• Easy to install, HSRM can be cut to any length (up to max circuit length) in the field.
• HSRM features lower installed cost than steam tracing, less maintenance expense and less down time.

New product on our website: Chromalox HSRL Self-Regulating Low Temperature Heating Cable for Process Temperature Maintenance

New product on our website: Chromalox HSRL Self-Regulating Low Temperature Heating Cable for Process Temperature Maintenance

https://morelectricheating.com/products/MANUFACTURERS/CHROMALOX/HEATCABLE/HSRL.aspx

HSRL Self-Regulating Low Temperature
• Approximate Size 3/8″W x 1/8″H
• Available in 3, 5, 8 and 10 Watts per Foot
• Available in 120 and 208-277V models
• Third-party certifications: CSA, FM
• Process Temperature Maintenance to 150°F (65°C)
• Maximum Continuous Exposure Temp, Power Off, 185°F (85°C)
• Circuit Lengths to 660 Feet
• T-Ratings see data sheet
• Min. Install Temp = -76°F (-60°C)
• Min. Bend Radius 1-1/8″
• For Use on Metal and Plastic Pipes & Tanks

• Energy efficient, self-regulating HSRL uses less energy when less heat is required.
• Easy to install, HSRL can be cut to any length (up to max circuit length) in the field.
• HSRL features lower installed cost than steam tracing, less maintenance expense and less down time.

New product on our website: Chromalox SRP Self-Regulating Process Temperature Heating Cable

New product on our website: Chromalox SRP Self-Regulating Process Temperature Heating Cable

https://morelectricheating.com/products/MANUFACTURERS/CHROMALOX/HEATCABLE/SRP.aspx

SRP Self-Regulating Process Temperature
• Approximate Size 3/8″W x 1/8″H
• Available in 5, 10, 15 Watts per Foot
• Available in 120 and 208-277V models
• Third-party certifications: FM
• Process Temperature Maintenance to 230°F (110°C)
• Maximum Continuous Exposure Temp, Power off, 275°F (135°C)
• Circuit Lengths to 750 feet
• T-Ratings – See data sheet
• Min. Install Temp = -76°F (-60°C)
• Min. Bend Radius 1-1/8″
• For use on Metal Pipes & Tanks

Chromalox SRP self-regulating heating cable provides safe, reliable heat tracing for process maintenance applications to 230°F (110°C) or freeze protection of pipes / tank with high heat losses. Constructed of industrial grade 16 AWG buss wire with a tinned copper braid and optional overjacketing, SRP ensures operating integrity most hostile industrial environments.

Because SRP is self-regulating, overtemperature conditions are minimized. Chromalox U-Series Connection Kits reduce installation time.

• Freeze Protection
• Freeze Protection, High Exposure Temperature
• Process Maintenance, Low Temperature
• Process Maintenance, High Temperature

Features of SRP Cable

• Max. Maintenance Temp. (°F) 225
• Max. Exposure Temp. (°F) Power Off 275
• Max. W/Ft. 15
• Max. Circuit Length (Ft.) 55-750
• Buss Wire Size 16
• Voltages 120, 208-270
• Hazardous Ratings Yes
• Usable on Plastic Pipe No
• Cut-to-Length in Field Yes
• Field Splicable Yes
• Can be Overlapped Yes
• Output Varies with Temp. Yes
• Varies Output Along Length Yes
• Accessories D/UL
• Monitor Wire Available Yes

SRP Corrosion Selection Guide

• Moisture C, CT
• Aqueous Solutions of Inorganic Compounds CT
• Liquids Organic Chemicals Acids or Bases CT
• Acids or Bases CT
C – Tin-Plated copper metallic braid for additional protection and ground path
CT – Fluoropolymer corrosion resistant overjacket over braid for hostile/corrosive environments
This is a recommendation guide. Chromalox cannot warrant any Electric Heat Trace against failure by sheath degradation if such failure is the result of operating conditions beyond the control of the heater manufacturer. It is the responsibility of the purchaser to make the ultimate choice of sheath material based on knowledge of the chemical composition of the corrosive solution, character of materials entering the solution, and controls which maintains the process.

 

New product on our website: Chromalox PIT Non-Indicating Bulb and Capillary Temperature Controllers

New product on our website: Chromalox PIT Non-Indicating Bulb and Capillary Temperature Controllers

https://morelectricheating.com/products/MANUFACTURERS/CHROMALOX/HEATCABLE/PIT.aspx

PIT Non-Indicating Temperature Controllers – PIT
• Bulb and Capillary
• UL Listed (PIT, PIT-EP only)

For a variety of process applications requiring rain-tight or explosion-resistant enclosure, PIT controllers may be used in pipe tracing and snow melting applications with electric heating cable.

New product on our website: Chromalox UESL End Seal Signal Light Kit

New product on our website: Chromalox UESL End Seal Signal Light Kit

https://morelectricheating.com/products/MANUFACTURERS/CHROMALOX/HEATCABLE/UESL.aspx

UESL End Seal Signal Light Kit
• Use With: SRL, SRP, SRM/E, CWM, SRF, HWM
• Third-party certifications: CSA and FM

NEMA 4X rated end seal designed to seal one cable and indicate power on with universal voltage 120-277 LED indicator light kit designed for use with SRL, SRP, SRM/E and CWM cables. This model provides water-resistant cable entry, enclosure support, terminal block, and corrosion-resistant wiring enclosure. A pipe strap (PS Series) is required to attach this model to a pipe. Small pipe adapter is available for pipe size less than 1-1/2″.

New product on our website: Chromalox CL-1 Caution Labels

New product on our website: Chromalox CL-1 Caution Labels

https://morelectricheating.com/products/MANUFACTURERS/CHROMALOX/HEATCABLE/CL-1.aspx

CL-1 Caution Labels

5 electric heat tracing caution labels, weather resistant.

New product on our website: Chromalox UAS Ambient-Sensing Thermostat Power Connection Kit

New product on our website: Chromalox UAS Ambient-Sensing Thermostat Power Connection Kit

https://morelectricheating.com/products/MANUFACTURERS/CHROMALOX/HEATCABLE/UAS.aspx

UAS Ambient-Sensing Thermostat Power Connection Kit
• Use With: SRL, SRP, SRM/E, CWM, SRF, HWM

NEMA 4X rated junction box designed to connect a single SRL, SRP, SRM/E or CWM cable run to power and control cable output via ambient air temperature in non-hazardous areas. This kit provides water-resistant cable entry for one cable, enclosure support, terminal block and a water resistant corrosion resistant wiring enclosure with a 3/4″ opening to accept a conduit hub (CCH-2 or equal). Stainless steel sheath probe is 9/16″ diameter x 3″ long. Switch rated for 22 amps SPDT 120-480 volts. Operating temperature range is -40°F to 160°F (-40°C to 71°C). Temperature set point 0° to 225°F (-81°C to 107°C) with 10°F scale divisions.

New product on our website: Chromalox FT-3 Fiberglas® Pipe Tape. 66 foot roll glass cloth tape with pressure- sensitive thermosetting silicone adhesive 3/8″ wide.

New product on our website: Chromalox FT-3 Fiberglas® Pipe Tape. 66 foot roll glass cloth tape with pressure- sensitive thermosetting silicone adhesive 3/8″ wide.

https://morelectricheating.com/products/MANUFACTURERS/CHROMALOX/HEATCABLE/FT-3.aspx

FT-3 Fiberglas® Pipe Tape

66 foot roll glass cloth tape with pressure- sensitive thermosetting silicone adhesive 3/8″ wide. 310F rating. Strap at one foot intervals at minimum application temperatures of -40F (-40°C).

EasyHeat Launhes New Self-Regulating Heating Cable Video on YouTube

EasyHeat Launches New Self-Regulating Heating Cable Video on YouTube

New product on our website: Chromalox RDK Downspout Hanger Kit for Heat Trace Cable

New product on our website: Chromalox RDK Downspout Hanger Kit for Heat Trace Cable

https://morelectricheating.com/products/MANUFACTURERS/CHROMALOX/HEATCABLE/RDK.aspx

RDK Downspout Hanger Kit for Heat Trace Cable
• Use With: SRF-RG and TW-Melt
• Third-party certifications: UL Listed, CSA, FM

The RDK-1 Downspout Hanger Kit is used to suspend and prevent damage to Chromalox Roof and Gutter Heating Cable as it enters gutter downspout. This kit contains material for one downspout entrance.

New product on our website: Chromalox RG-SK Splice & Tee Kit for use With: SRF-RG, TW-Melt and TW-Wrap Heating Cables

New product on our website: Chromalox RG-SK Splice & Tee Kit for use With: SRF-RG, TW-Melt and TW-Wrap Heating Cables

https://morelectricheating.com/products/MANUFACTURERS/CHROMALOX/HEATCABLE/RG-SK.aspx

RG-SK Splice & Tee Kit
• Use With: SRF-RG, TW-Melt and TW-Wrap
• Third-party certifications: UL Listed, CSA, FM

Use to make water resistant seal for Connecting two or three heating Cables together at one point. Includes materials for two splice or two tee connections.

New product on our website: Chromalox RT-RES End Seal Kit for use With: SRL, SRM/E, CWM, SRF

New product on our website: Chromalox RT-RES End Seal Kit for use With: SRL, SRM/E, CWM, SRF

https://morelectricheating.com/products/MANUFACTURERS/CHROMALOX/HEATCABLE/RT-RES.aspx

RT-RES End Seal Kit
• Use With: SRL, SRM/E, CWM, SRF
• Third-party certifications: UL Listed, CSA, FM

The RT-RES kit is used for terminating braided (-C) and overcoated (-CR) cables in ordinary locations. Consult factory for installation of braided cable in hazardous locations. Check the kit label to ensure you have the proper kit for the cable you are installing. This kit contains enough parts to make five (5) end seals. Materials required include: sharp utility knife, standard electrical cutters, propane torch or heat gun, needle nose pliers and fiberglass tape (Chromalox FT-1 or equal).